High Speed Door Servo Motor and Controller
Match a high speed door drive to the curtain, transmission and required operating cycle. Review motor torque, controller functions, encoder, braking and sensor interfaces before selecting a replacement or new system.
Send YUOU your door type, curtain weight, dimensions, drum or transmission details, voltage, target speed and controller interfaces for a configuration-based quotation. Review the selected equipment and installation requirements before confirming the order.
Technical Data
| Rated Output Power | 0.75KW | 1.5KW | 2.2KW |
| Rated Speed | 2,000rpm | 2,000rpm | 2,000rpm |
| Power Supply | 220V±10% | 220V±10% | 220V±10% |
| RatedTorque | 3.6Nm | 7.2Nm | 15Nm |
| Heating | <30℃ | <30℃ | <30℃ |
| Working Temperature | -10℃-40℃ | -10℃-40℃ | -10℃-40℃ |
| Torque Management System | AutomaticTorque | AutomaticTorque | AutomaticTorque |
| Maximum Operating Width | <16㎡ | <30㎡ | <60㎡ |
| Limit Mode | AbsoluteEncoder | AbsoluteEncoder | AbsoluteEncoder |
| Self Locking Mode | Electro Mechanical Brake | Electro Mechanical Brake | Electro Mechanical Brake |
| ManualRelease | HandCrank | HandCrank | HandCrank |
| Weight | 4.9KG | 8.1Kg | 15.6Kg |
Product Details
Use the following product details to compare suppliers against the same project requirements. YUOU can review these items with your drawings before the final configuration and quotation are confirmed.
Servo Motor and Transmission
The motor, brake and encoder must suit the door load and transmission. Rated power alone does not establish compatibility with an existing curtain or gearbox.
Provide dimensions, curtain weight, shaft and mounting details, drum size, target speed and daily cycles for drive selection.
Controller and Sensor Interfaces
The controller coordinates the motor with activation and protective devices. Input types, output capacity and signal logic must match the equipment connected to it.
Confirm supply voltage, encoder compatibility, limit setup, safety inputs and restart procedure. Building-control integration requires a defined interface specification.
Why Specify a YUOU High Speed Door Servo Motor and Controller?
Compare the configuration, not just the price: match these details to your opening and daily workflow.
Drive-Load Matching
Select motor power and torque from the door load and transmission, not opening area alone.
Controlled Acceleration
Servo control can tune starting and stopping behavior to the door mechanism and traffic needs.
Encoder-Based Positioning
The listed absolute encoder supports position feedback; setup and recovery requirements depend on the complete system.
Brake and Manual Release
Confirm brake compatibility and the manual crank procedure for the chosen motor.
Sensor Interface Review
Check signal types and controller inputs for photocells, safety edges and activation devices.
Clear Replacement Scope
Confirm mounting, shaft, cable, controller and firmware compatibility before replacing an existing drive.
High Speed Door Servo Motor and Controller FAQ
Can I replace my existing motor with one of the same power?
Not on power alone. Check torque, speed, gearbox, shaft, mounting, brake, encoder and controller compatibility.
Does a 2.5 m/s door speed follow from the motor rating?
No. Door speed also depends on transmission, drum size, curtain load and control settings. The motor should be selected from the complete mechanism.
Does an absolute encoder eliminate all setup after a power loss?
No. Position feedback does not remove the need for commissioning, fault checks or the correct restart procedure for the controller and door.
Can it connect to any radar or building-control system?
No. Confirm voltage, signal type, input/output capacity and required communication protocol before assuming compatibility.
What information is needed for a high speed door servo motor and controller quotation?
Send door type, curtain weight, dimensions, drum or transmission details, voltage, target speed and controller interfaces. Include drawings or site photos where available so the configuration, installation scope and required options can be confirmed.
Inside YUOU Manufacturing
View the production environment and manufacturing work shown in the YUOU factory video. Confirm the production, inspection and supply scope for your project in the quotation.
High Speed Door Servo Motor and Controller Guides
Request a Quote for Your Project
Share the products, approximate sizes and quantities you need. We will review your requirements and confirm quotation details with you.
Not sure about the specifications? Send the details you have.
- Factory-direct quotationDiscuss your purchasing requirements directly with the manufacturer and clarify the details behind your quotation.
- Configuration reviewReview sizes, materials and operating requirements with our team to help select a suitable configuration.
- Installation guidanceInstallation documents and remote guidance are available to support your local installation team.
- One enquiry, multiple productsList different products together, or attach your purchasing list, photos or drawings for review.